AKAG TOY

Flash Hider Induction Tactical Lighter Flame Hog Silencer for 14mm CCW and 19mm

$12.99 USD

Sale Sold out

Taxes included. Shipping calculated at checkout.

colour flame hog + 14mm ccw

Description:
-This luminous silencer is suitable for gel balls, which can make the gel balls produce luminous effects.

-Built-in battery

-Material: ABS plastic

-Interface: 14mm CCW/19mm

-Supported projectile type: gel ball

-Ballistic inner diameter: 11mm

-Interface inner diameter: 19mm

Operating Instructions:
-Fill the smoke oil.

-Click the button and the yellow bulb will light up once, indicating that the device will emit smoke only.

-Click the button again and you can switch between three modes - smoke only, flame only, or smoke and flame mode.

-Click the button and hold for 3 seconds, the red bulb will light up once, indicating that the minimum amount of smoke will be emitted.

-Click the button again and hold for 3 seconds, the red light will light up 2 times, indicating that a medium amount of smoke will be emitted.

-Click the button a third time and hold for 3 seconds, indicating that the maximum amount of smoke will be emitted.

-If the device is not used for 20 minutes, it will automatically turn off. Be sure to remove the battery after use.

Packing list:
1*luminous silencer
1USB charging cable
1*14mm ccw to 19 interface

We Promise

We offer free shipping and tax exemption worldwide. If you are unable to pay or have questions about the payment amount, please contact us.
If the product or accessory you want to buy is not shown on our website, please send us a message and we will solve it for you as soon as possible.
Secure payment via Shopify Payments or PayPal.
We use encrypted SSL certificates to ensure 100% security.
Customer service responds to messages 24 hours a day.
30-day money back guarantee.If you are not completely satisfied with the product for any reason, you can initiate a return within this period.
Based on past experience, 99% of packages pass through customs smoothly. If your package is unfortunately detained by customs, we will resend it or provide a full refund. We guarantee that our customers will not suffer any loss.
If you do not have a pleasant shopping experience, please contact us at service@akagtoy.com, we will provide you with satisfactory service and make you 100% satisfied.

Soaking Requirements: It is best to use purified water, and sufficient water is essential. Impure water will cause the gel balls to shrink, which can result in reduced range or even inability to shoot.
Soaking Time: Soak the gel balls for 4-6 hours to ensure full expansion.
How to Use: Before loading the gel ball into the magazine, drain the water first to prevent moisture from damaging the circuit.
Storage: After soaking, drain the water and store them tightly sealed. Gel balls that have been soaked for too long or not properly can break or get stuck, making them inoperable.
7-8mm super-hard frosted balls are best for electric pistol toys; other sizes break easily.
Standard Size: 7.15mm - 7.3mm (fits most gel blasters).

When using a battery for the first time, fully charge it. Do not charge the battery through the discharge port.
Use a charger with a voltage balancing function to charge the device.
If you notice a drop in power during use, discontinue use. Leave approximately 10% of the battery charge in the battery. Do not drain the battery completely to avoid damage caused by over-discharge.
For gel blasters with electronic speed control or fire control, remove the battery after use to avoid permanent damage.
The 7.4V battery consists of two cells, and the 11.1V battery consists of three cells. The voltage of a single cell should not be lower than 3.3V or higher than 4.2V. Store the device between 3.8-3.9V for extended periods.
Overheating of the motor may cause the battery to expand or even ignite. Please inspect your device carefully and use with caution. Do not use the battery if it is damaged or bulging.
If the battery does not fully charge after a long period of time, use a baby ring to check the voltage of each cell.
Remove the battery when not in use to extend the life of the transmitter.